| Amplifier Model |
IPX10:8 |
| OUTPUT POWER |
| Low-Z mode: Load Impedance |
2Ω |
2.7Ω |
4Ω |
8Ω |
| Maximum Output Power1 |
|
| Normal Mode, all channels driven |
1300 W |
1500 W |
1250 W |
1250 W |
| Bridged |
– |
– |
2600 W |
2500 W |
| Parallel |
2500 W |
3000 W |
2500 W |
1250 W |
| Parallel-Bridged |
5200 W |
6000 W |
5000 W |
5000 W |
| Direct Drive Mode: Nominal Voltage |
70 V |
100 V |
140 V2 |
200 V2 |
| Maximum Output Power1 |
1250 W |
1250 W |
2500 W |
2500 W |
| Number of amplifier channels |
8 |
| Maximum Output Voltage, Normal mode, per channel |
150 Vpeak |
| Maximum Output Current, Normal mode, per channel |
41 Apeak |
| AMPLIFIER |
| Voltage Gain |
|
| Low-Z mode, ref. 1 kHz |
32.0 dB, adjustable 20.0 — 44.0 dB |
| Direct Drive mode |
33.2 / 36.2 / 39.2 / 42.2 dB for 70 / 100 / 140 / 200 V |
| Input Sensitivity |
|
| Low-Z mode, Max. Output Voltage |
10.7 dBu (2.66 V), adjustable -1.3 — 22.7 dBu |
| Direct Drive mode |
6 dBu (1.55 V), fixed |
| THD 3 dB below max, AES17, 1 kHz |
< 0.05 % |
| DIM 100 3.15 kHz, 15 kHz |
< 0.15 % |
| IMD-SMPTE, 60 Hz, 7 kHz |
< 0.05 % |
| Crosstalk ref. 1 kHz, 12 dB below Max, 8 Ω |
< -80 dB |
| Frequency Response, ref. 1 kHz, analog in to speaker out |
20 Hz to 20 kHz (±0.5 dB) |
| Damping Factor, 20 Hz to 200 Hz, 8 ± |
> 400 |
| Output Stage Topology |
Class D, fixed frequency |
| Signal to Noise Ratio Amplifier |
|
| A-weighted, analog input |
112 dB |
| A-weighted, digital input |
115 dB |
| Output Noise |
|
| A-weighted, analog input |
< -70 dBu |
| A-weighted, digital input |
< -73 dBu |
| CONNECTIVITY |
| Analog Audio Input/Thru |
|
| Type |
4 x 6-pin Euroblock, male |
| Maximum Input Level |
+21 dBu |
| Input Impedance, active balanced |
20 ㏀ |
| Reference level equal to digital input |
+21 dBu for 0 dBFS |
| Speaker Output |
2 x 8-pin Euroblock, 6mm, female |
| GENERAL |
| Power Consumption |
|
| Rated power consumption (see BTU table) |
1300 W |
| ⅛ Maximum Output Power at 4 Ω |
1780 W |
| Idle Mode (no input signal) |
105 W |
| Standby Mode |
< 18 W |
| Dimensions (W x H x D), mm |
483 x 88.1 x 514.2 |
| Weight |
16.8 kg (37.1 lb) |
| Shipping Weight |
19.1 kg (42.1 lb) |
| DIGITAL SIGNAL PROCESSING |
| Sampling Rate |
48 kHz / 96 kHz, OMNEO/Dante synchronized |
| Signal delay/latency Analog In to Speaker Out, 48 kHz/96 kHz |
0.70 ms / 0.53 ms |
| Dante Network Latency |
typ. 1.00 ms |
| Signal Processing |
|
| User EQ |
12 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, HiPass, Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type |
| User Delay |
0 to 2000 ms per channel (units: µs, ms, s, cm, m, inches, feet) |
| Array EQ |
5 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Hi-Pass, LoShelvQ, HiShelvQ, Lo-Pass & All-Pass |
| Array Delay |
0 to 500 ms per channel (units: µs, ms, s, cm, m, inches, feet) |
| Speaker EQ |
10 filters per channel, selectable as PEQ, LoShelv, Hi-Shelv, Hi-Pass, Lo-Pass & All-Pass |
| Speaker X-Over |
Hi-Pass, & Lo-Pass per dB channel, 6/12/18/24/30/36/42/48 dB Bessel/ Butterworth, 12/24/48 Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel |
| Speaker FIR |
Up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over |
| Speaker Limiters |
Peak Anticipation Limiter & RMS/TEMP Limiter per channel |
| Other Functions |
Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Pilot Tone Generator & Detection, Level Meters, Impedance Measurement & Load Monitoring |
| Memory |
|
| DSP Presets |
1 factory preset + 20 user presetsr |
| Speaker-Pool Presets |
30 speaker settings |
| Source Supervision & Fallback |
Pilot Tone supervision at Analog & OMNEO/Dante inputs, switchover to alternative Source Selection |
| CONNECTIVITY |
| Network |
|
| Type |
2 x Neutrik EtherCON/RJ45, redundant PRIMARY/SECONDARY |
| General |
1000base-T/100base-TX, integrated switch |
| Network Audio Inputs |
8 channels, 48/96 kHz, OMNEO/Dante format |
| Network Audio Outputs (Monitor) |
2 channels, 48/96 kHz, OMNEO/Dante format |
| Mains Input |
1 x Neutrik powerCON-HC |
| GPIO Control Port |
|
| Type |
1 x 8-pin Euroblock, male |
| Ports & Operating Modes |
3 x GPIO, switchable Analog In/Digital In/Digital Out |
| Analog Input Range |
0 V to +13 V, 40 ㏀ input resistance |
| Digital Input Limits |
ON: < 1.5 V /
OFF: > 2.0 V, internal Pull Up (10 ㏀) |
| Digital Outputs |
ON: Output switched to GND, max. 200 mA
OFF: Open Collector (40 ㏀ to GND) |
| Reference Voltage Output |
+10 V, max. 200 mA, supervised, short circuit protected |
| READY/FAULT contact |
Galvanic isolated relay, max. 30 VDC/500 mADC |
| GENERAL |
| User Interface |
|
| Display |
Black/white OLED 256 x 64 |
| Front panel indicators |
4 x status LEDs (POWER, STANDBY, FAULT, OMNEO) |
| Front panel operating elements |
3 buttons (UP, ENTER, DOWN) |
| Rear panel indicators |
1 x status LED (STATUS) |
| Rear panel operating elements |
Mains Switch |
| Power Requirements |
100 V to 240 V, 50 Hz to 60 Hz AC |
| Power Supply Topology |
Switching Mode Power Supply with digital controlled Power Factor Correction |
| Protections |
Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over-/Under voltage Protection |
| Cooling |
Front-to-rear, temperature controlled fans, supervised |
| Ambient Temperature Limits |
+5 °C to +40 °C (+40 °F to +105 °F) |
| IEC Protection Class |
Class I (grounded) |
| Electromagnetical Environment |
E1, E2, E3 |
| Color |
Black |
Amplifier at rated conditions, Low-Z Normal operation mode, all channels driven, 4 Ω loads, Analog input, 32 dB Gain, 48 kHz sample rate, unless otherwise specified
1Test signal for max. output power according IHFA-202 (Dynamic-Headroom, burst 1 kHz / 20 ms on / 480 ms off / low level -20 dB).
2Available in Bridged operation mode only. |
