Music Space (Thailand)

Member

สินค้า

focusrite_rednet_hd32r

Focusrite RedNet HD32R Dante Networks Pro Tools|HD Bridge

Focusrite

Focusrite RedNet HD32R, 2 inputs and 32 outputs from your RedNet network direct into Pro Tools | HD via DigiLink, Supported sample rates: 44.1, 48, 88.2, 96, 192kHz, Word Clock Input Output via BNC port, Dante Ethernet port

135,000 ฿

ราคาสินค้าไม่รวมภาษีมูลค่าเพิ่ม
หมวดหมู่: ป้ายกำกับ:

คำอธิบาย

Focusrite RedNet HD32R 32-Ch Bridge between Dante Networks and Pro Tools|HD

Focusrite RedNet HD32R, 2 inputs and 32 outputs from your RedNet network direct into Pro Tools | HD via DigiLink, Supported sample rates: 44.1, 48, 88.2, 96, 192kHz, Word Clock Input Output via BNC port, Dante Ethernet port

RedNet HD32R is a 1U, 19in rack-mount Dante interface that allows Pro Tools|HD users direct access to the full benefits of the Dante digital audio networking system, including its uniquely flexible network topology and premium quality audio interfaces.

The Pro Tools system is connected to the HD32R via standard Mini DigiLink ports. HD32R acts as a 64-channel (32 in/32 out) digital break in/out box, operating in the same way as a standard interface, and supporting a wide range of Pro Tools|HDX and HD cards. Up to six HD32R modules can be used with a Pro Tools|HDX system and three with Pro Tools|HD, allowing the maximum channel count for either.

The HD32R features a rugged, roadworthy exterior and high internal build quality, with Ethernet and power supply redundancy. In addition, it offers a compact 1U rack-mount form factor for a full 32 channels of I/O.

Features:

  • Allows Dante Ethernet-based audio networking products to interoperate fully with Pro Tools|HD & Pro Tools|HDX
  • Ethernet and power supply redundancy with auto switchover in case of failure and locking connectors
  • Provides the vital link to create an extensive high-quality audio network based on standard Cat 5e or Cat 6 wiring, bringing the latest advances in digital audio networking to Pro Tools|HD
  • Cost-effectively increase audio I/O quality and flexibility with RedNet interfaces
  • Permits multiple workstations to access the same interface hardware and I/O
  • No changes to Pro Tools workflow required – simple, logical assignment of RedNet I/O to Pro Tools|HD inputs and outputs
  • Up to 32 I/O with Pro Tools|HD over single DigiLink connection per RedNet HD32R
  • Additional Avid/Digidesign interfaces may be connected to expansion ports
  • Upgrade to RedNet interfaces while remaining fully compatible with TDM- or AAX-DSP-based plugins and saved sessions
  • Comprehensive remote control software with powerful graphic user interface

Specifications

Connectors (Rear Panel) 2 x etherCON locking Ethernet connectors ( compatible with standard RJ45 connectors)
2 x BNC Word Clock In and Out (with switchable 75 ohm input termination)
2 x BNC Loop Sync I/O (75 ohm port)
2 x Mini DigiLink connectors to/from Pro Tools|HD system (Primary and Expansion)
2 x IEC power inputs (with retaining clips)
Controls Power on/off
Digital Performance Clock Sources: Internal, Word Clock, Loop Sync (master or slave) or from Dante Network Master
Sample Rates: 44.1 / 48 / 88.2 / 96 / 176.4 / 192 kHz (-4 / -0.1 / +0.1 / +4.167%) at 24 bit
Ext. Word Clock Range: nominal sample rate ±7.5%
Indicators Primary PSU (A): Green LED – Illuminates when an AC input is applied and all DC outputs are present.
Primary PSU (B): Green LED – Illuminates when an AC input is applied and all DC outputs are present.
Primary Network: Green LED – Indicates that a network connection is present on primary port when in redundant mode. When in Switched mode, a valid network connection at either Primary or Secondary network port will cause this LED to illuminate.
Secondary Network: Green LED – Indicates that a network connection is present on secondary port when in redundant mode. Not used in switched mode.
Network Locked: Green LED – When unit is network slave, shows valid network lock. When network master, shows lock to indicated clock source. Flashing indicates external clock is selected but not connected.
Sample Rate: Orange LED – For each: 44.1 kHz, 48 kHz, x2, x4.
Pull Up/Down: Orange LED – Indicates unit is set to operate on a Dante pull up/down domain.
Signal Indicators: 16 x Green LEDs, 8 input/8 output indicators. Illuminate @ -126 dBFS.
Clock Source: Orange LED for each – Internal, Word Clock, Loop Sync and DAW Master.
Network Modes Redundant: Allows unit to connect two independent networks
Switched: Connects both ports to integrated network switch, allowing daisy-chaining of device
Supported Systems Pro Tools|HD PCIe
Pro Tools|HDX
Pro Tools|HD Native PCIe
Pro Tools|HD Native Thunderbolt
System Requirements Requires Pro Tools|HD 8.0 and up
PSU 2 x internal; IEC inputs, 100 to 240 VAC, 50/60 Hz
Apparent Power: 30 VA
Dimensions (H x W x D) 1.75 x 19 x 10.35″ (44.5 x 482.6 x 263 mm)
Weight 8.6 lb (3.9 kg)
Packaging Info
Package Weight 12.25 lb
Box Dimensions (LxWxH) 24.0 x 15.433 x 4.567″

Downloads

ดาวน์โหลด USER GUIDE, SOFTWARE, BROCHURE Focusrite RedNet HD32R Dante Networks Pro Tools|HD Bridge

สินค้าที่เกี่ยวข้อง