| Number of Amplifier Channels |
4 |
| Maximum Output Voltage, Normal mode, per channel |
150 Vpeak |
| Maximum Output Current, Normal mode, per channel |
53 Apeak |
| AMPLIFIER |
| Voltage Gain |
| Low-Z mode, ref.1kHz |
32.0 dB, adjustable 20.0-44.0 Db |
| Direct Drive mode |
33.2/36.2/39.2/42.2 dB for 70/100/140/200 V |
| Input Sensitivity |
| Low-Z mode, Max. Output Voltage |
10.7 dBu (2.66 V), adjustable -1.3-22.7 dBu |
| Direct Drive mode |
6 dBu (1.55 V), fixed |
| THD3 dB below max, AES17, 1 kHz |
< 0.05 % |
| DIM 1003.15 kHz, 15 kHz |
< 0.15 % |
| IMD-SMPTE60 Hz, 7 kHz |
< 0.05 % |
| Crosstalk ref. 1 kHz, 12 dB below Max, 8 Ω |
< -80 dB |
| Frequency Responseref. 1 kHz, analog into speaker out |
20 Hz to 20 kHz (±0.5 dB) |
| Damping Factor 20 Hz to 200 Hz, 8Ω |
> 400 |
| Output Stage Topology |
Class D, fixed frequency |
| Signal to Noise Ratio Amplifier |
| A-weighted, analog input |
112 dB |
| A-weighted, digital input |
115 dB |
| Output Noise |
| A-weighted, analog input |
< -70 dBu |
| A-weighted, digital input |
< -73 dBu |
| CONNECTIVITY |
| Analog Audio Input/Thru |
| Type |
2 x 6-pin Euroblock, male |
| Maximum Input Level |
+21 dBu |
| Input Impedance, active balanced |
20 kΩ |
| Reference level equal to digital input |
+21 dBu for 0 dBFS |
| Speaker Output |
1 x 8-pin Euroblock, 6 mm, female |
| GENERAL |
| Power Consumption |
|
| Rated power consumption (see BTU table) |
1200 W |
| ⅛ Maximum Output Power at 4 Ω |
1765 W |
| Idle Mode (no input signal) |
80 W |
| Standby Mode |
< 16 W |
| Dimensions (W x H x D), mm |
483 x 88.1 x 514.2 |
| Weight |
15.0 kg (33.0 lb) |
| Shipping Weight |
17.2 kg (37.8 lb) |
| DIGITAL SIGNAL PROCESSING |
| Sampling rate |
48 kHz/96 kHz, OMNEO/Dante synchronized |
| Signal delay/latency Analog In to Speaker Out, 48 kHz/96kHz |
0.70 ms/0.53 ms |
| Dante Network Latency |
typ. 1.00 ms |
| Signal Processing |
| User EQ |
12 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass,Lo-Pass & Notch; 2 filters of them with additional asymmetric filter type |
| User Delay |
0 to 2000 ms per channel (units: μs, ms, s, cm, m, inches, feet) |
| Array EQ |
5 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Lo-ShelvQ, Hi-ShelvQ, Hi-Pass, Lo-Pass, & All-Pass |
| Array Delay |
0 to 500 ms per channel (units: μs, ms, s, cm,m, inches, feet) |
| Speaker EQ |
10 filters per channel, selectable as PEQ, Lo-Shelv, Hi-Shelv, Hi-Pass, Lo-Pass & All-Pass |
| Speaker X-Over |
Hi-Pass, & Lo-Pass per channel,6/12/18/24/30/36/42/48 dB Bessel/Butterworth,12/24/48 dB Linkwitz-Riley; Alignment Delay, 0 to 20 ms per channel |
| Speaker FIR |
Up to 1025 taps, Linear Phase Filter, Linear Phase Brickwall X-Over |
| Speaker Limiters |
Peak Anticipation Limiter & RMS/TEMP Limiterper channel |
| Other Functions |
Source Selection & Mix, Level, Mute, Polarity, Sine & Noise Generator, Pilot Tone Generator & Detection, Level Meters, Impedance Measurement & Load Monitoring |
| Memory |
| DSP Presets |
1 Factory + 20 User |
| Speaker-Pool Presets |
30 Speaker Settings |
| Source Supervision & Fallback |
Pilot Tone supervision at Analog & OMNEO/Dante inputs, switch over to alternative Source Selection |
| CONNECTIVITY |
| Network |
| Type |
2 x Neutrik EtherCON/RJ45, redundant PRIMARY/SECONDARY |
| General |
1000base-T/100base-TX, integrated switch |
| Network Audio Inputs |
8 channels, 48/96 kHz, OMNEO/Dante format |
| Network Audio Outputs (Monitor) |
2 channels, 48/96 kHz, OMNEO/Dante format |
| Mains Input |
1 x Neutrik powerCON-HC |
| GPIO Control Port |
| Type |
1 x 8-pin Euroblock, male |
| Ports & Operating Modes |
3 x GPIO, switchable Analog In/Digital In/Digital Out |
| Analog Input Range |
0 V to +13 V, 40 kΩ input resistance |
| Digital Input Limits |
ON: < 1.5 VOFF: > 2.0 V, internal Pull Up (10 kΩ) |
| Digital Outputs |
ON: Output switched to GND, max. 200 mA OFF: Open Collector (40 kΩ to GND) |
| Reference Voltage Output |
+10 V, max. 200 mA, supervised, short circuit protected |
| READY/FAULT contact |
Galvanic isolated relay, max. 30 VDC/500mADC |
| GENERAL |
| User Interface |
| Display |
Black/white OLED 256 x 64 pixel |
| Front panel indicators |
4 x status LEDs (POWER, STANDBY, FAULT, OMNEO) |
| Front panel operating elements |
3 buttons (UP, ENTER, DOWN) |
| Rear panel indicators |
1 x status LED (STATUS) |
| Rear panel operating elements |
Mains Switch |
| Power Requirements |
100 V to 240 V, 50 Hz to 60 Hz AC |
| Power Supply Topology |
Switching Mode Power Supply with digital controlledPower Factor Correction |
| Protections |
Audio Limiters, High Temperature, DC, HF, Short Circuit, Back-EMF, Peak Current Limiters, Inrush Current Limiters, Turn-on Delay, Mains Circuit Breaker Protection, Mains Over-/Undervoltage Protection |
| Cooling |
Front-to-rear, temperature controlled fans, supervised |
| Ambient Temperature Limits |
+5 °C to +40 °C (+40 °F to +105 °F) |
| IEC Protection Class |
Class I (grounded) |
| Electromagnetical Environment |
E1, E2, E3 |
| Color |
Black |
Amplifier at rated conditions, Low-Z Normal operation mode, all channels driven, 4 Ω loads, Analog input, 32dB Gain, 48 kHz sample rate, unless otherwise specified.
1Test signal for max. output power according IHFA-202 (Dynamic-Headroom, burst 1 kHz/20 ms on/480ms off/low level -20 dB).
2Available in Bridge operation mode only. |
